Customise Your Ride
Set up speed units, cruise control, kick-to-start and drivetrain behaviour so your scooter feels exactly how you like to ride.
How to Access the P Settings Menu
These steps apply to scooters that use the P-menu (Kaiju & Aurora).
- 1 Power on your scooter.
- 2 Hold Power + Function until you see P0.
- 3 Use the buttons to scroll through P1, P2, P3…
- 4 Press Function to change a value.
- 5 Press Power once to go back.
- 6 Hold Power + Function again to save & exit.
How to Access the Settings Menu
These steps apply to Edgerunner’s on-display settings menu.
- 1 Power on your scooter.
- 2 Hold the top and bottom buttons on the gear selector until the settings menu appears.
- 3 Use the selector to scroll through settings.
- 4 Change values using the selector/buttons (depending on the option).
- 5 Repeat the button hold to save & exit (if required).
Kaiju & Aurora – P Settings
Tap a setting to expand.
Change how speed is displayed on your screen.
| Value | Effect |
|---|---|
| 0 | km/h (metric) |
| 1 | mph (imperial) |
Tip
- This only changes what’s shown on the display — it doesn’t change the scooter’s power output.
Allows the scooter to maintain a constant speed after holding the throttle steady.
| Value | Effect |
|---|---|
| 1 (default) | Cruise control ON. |
| 0 | Cruise control OFF. |
How to change it
- Go to P1 in the menu.
- Select 0 or 1.
Controls whether the scooter can accelerate from standstill (zero-start) or needs a light push first (kick-to-start).
| Value | Effect |
|---|---|
| 0 | Zero-start enabled. |
| 1 (default) | Kick-to-start enabled. |
Controls which motors drive the scooter.
| Value | Motor Mode |
|---|---|
| d | Dual motor |
| f | Front motor only |
| b | Rear motor only |
Important
- Single motor mode reduces performance.
- Extra strain on one motor — use for range emergencies only.
Edgerunner – Settings
The Edgerunner uses a similar on-display settings menu, but with a wider range of options. Use the table below as a reference.
| Setting | Function | Range | Default / Comments |
|---|---|---|---|
| P01 | Display brightness | 1 (darkest) → 3 (brightest) | 2 |
| P02 | Imperial vs. metric units | 0 = kilometres / 1 = miles | 0 |
| P03 | Battery voltage | Min: 24V / Max: 72V | 52V |
| P04 | Auto shut-off timer | Min: 1 minute / Max: 60 minutes | 5 minutes |
| P05 | Gear setting | 0-3, 0-5, 0-9, 1-3, 1-5, 1-9 | 1-3 |
| P06 | Wheel diameter (inches) | N/A | 10 inches |
| P07 | Motor magnet count | Min: 1 / Max: 100 | 30 |
| P08 | Performance limiter | Min: 5% / Max: 100% | 25 |
| P09 | Kick start vs. instant start | 0 = instant start / 1 = kick start | 0 |
| P10 | Not currently used | — | — |
| P11 | Electric brake strength | Min: 0 / Max: 3 | 1 (Warning: Level 3 is extremely powerful — test lightly at low speeds first.) |
| P12 | Acceleration strength | Min: 1 / Max: 5 | 3 |
| P13 | Not currently used | — | — |
| P14 | Not currently used | — | — |
| P15 | Controller cutoff voltage | Unit: 0.1V | 450 |
| P16 | Odometer reset | N/A | Press gear up or gear down for 2 seconds to reset odometer |
| P17 | Cruise control | 0 = off / 1 = on | Maintain constant speed for 5 seconds to activate cruise control |
Heads up: If you’re unsure about any setting (especially braking and acceleration), message our team before changing it.
Using the App (Astro)
The Astro uses the GreenDrive app for all riding and performance settings.
Click below to download the app.
Not sure which settings suit your riding style? Contact our support team and we’ll help you tune it perfectly.